[Gelöst] OpenStage 40 Fehler RF2 an FritzBox

[mcmods]

Moin, hab mein 40er HFA V3 mit der Firmware OS40_SIP_V3_R5_17_0 bestückt und soweit "eingerichtet" jedoch bekomme es nicht hin das es läuft

hab auch das mit dem 8 Buchstaben etz. eingegeben... jedoch lüppt einfach nicht.....

Diagnose Übersicht

2021-02-17 17:45:31
00 Terminal number	10000620
01 SIP server	192.168.178.1
02 SIP port	5060
03 SIP registrar	192.168.178.1
04 SIP registrar port	5060
05 SIP gateway	None
06 SIP gateway port	5060
07 SIP transport	UDP
08 TLS renegotiation	Secure (RFC5746)
09 SIP local	5060
10 Server features	No
11 DNS results	none
12 Multiline	No
13 Keyset lines	None
14 Backup active	Yes
15 Backup proxy	None
16 Use secure calls	No
17 SDES status	Disabled
18 SIP server cert. check	No certificate check
19 Software version	V3R5.17.0 SIP 190920
20 Display message	Telefonie ausgefallen (RF2)
21 Last restart	2021-02-17T17:34:57
22 Memory free	30740K free
23 Protocol mode	IPv4_IPv6
24 IP4 address	192.168.178.84
25 IP4 subnet mask	255.255.255.0
26 IP4 default route	192.168.178.1
27 Primary DNS	192.168.178.1
28 Secondary DNS	None
29 IP4 route 1 IP	None
30 IP4 route 1 gateway	None
31 IP4 route 1 mask	None
32 IP4 route 2 IP	None
33 IP4 route 2 gateway	None
34 IP4 route 2 mask	None
35 IP6 address	None
36 IP6 prefix length	None
37 IP6 global gateway	None
38 IP6 link local addr	None
39 IP6 route 1 dest	None
40 IP6 route 1 pref len	None
41 IP6 route 1 gateway	None
42 IP6 route 2 dest	None
43 IP6 route 2 pref len	None
44 IP6 route 2 gateway	None
45 MAC address	001ae872b60f
46 LLDP	Yes
47 VLAN discovery	LLDP-MED
48 DHCPv4	Yes
49 DHCPv4 re-use	No
50 DHCPv6	Yes
51 DHCPv6 re-use	No
52 LAN port type	Automatic
53 PC port status	Disabled
54 PC port type	Automatic
55 PC port autoMDIX	No
56 VLAN ID	None
57 QoS Layer 2	Yes
58 QoS Layer 2 voice	5
59 QoS Layer 2 signalling	3
60 QoS Layer 2 default	0
61 QoS Layer 3	Yes
62 QoS Layer 3 voice	EF / 46
63 QoS Layer 3 signalling	AF31 / 26
64 LLDP-MED operation	Sent: Wed Feb 17 17:45:30 2021 Chassis ID TLV Data .Subtype = Network address .IANA_TYPE = IPv4 Address .ID = 192.168.178.84 Port ID TLV Data .Subtype = MAC address .ID = 00:1A:E8:72:B6:0F TTL TLV data .seconds = 120 System Caps TLV Data .Supported = Bridge, Telephone, .Enabled = Telephone, MAC_Phy config TLV data .Auto-set supported = Yes .Auto-set enabled = Yes .PMD = 0x6c00 .PMD1 = 10BASE-T half duplex mode .PMD2 = 10BASE-T full duplex mode .PMD3 = 100BASE-TX half duplex mode .PMD4 = 100BASE-TX full duplex mode .MAU = 100BaseTXFD : 0x10 LLDP-MED Caps TLV Data .Caps - LLDP-MED = Yes .Caps - Network Policy = Yes .Caps - Location ID = No .Caps - Extended Power Mdi PD = Yes .Caps - Extended Power Mdi Pse = No .Caps - Inventory = No .Type = Endpoint Class III Network policy (Voice) TLV data .Policy unknown = Yes .Tagged = No .VLAN ID = 0 .Layer 2 priority = 0 .DSCP = 0 Network policy (Voice Signalling) TLV data .Policy unknown = Yes .Tagged = No .VLAN ID = 0 .Layer 2 priority = 0 .DSCP = 0 Network policy (Video conferencing) TLV data .Policy unknown = Yes .Tagged = No .VLAN ID = 0 .Layer 2 priority = 0 .DSCP = 0 Extended Power TLV data .Type = PD .Source = Unknown .Priority = Critical .Power value = 46 Received: Wed Feb 17 17:45:30 2021 TTL TLV data .seconds = Network policy .TLV not available
65 NG911 location	Disabled
66 FIPS enabled	No

einer ne Idee ?

 

[KunterBunter]

Ja, natürlich 'ne Idee. Fritzbox neustarten.

 

[mcmods]

ähm ja....... guten Morgen.. DANKE