Hallo,
habe bei Asterisk das Modul chan_dongle hinzugefügt und es scheint auch zu funktionieren:
Der Huawei USB Stick wird auch erkannt:
dongle.conf wurde mit der IMEI Nummer versorgt:
Und trotzdem findet Asterisk den USB Stick nicht.
Hat jemand eine Idee was ich noch tun muß oder wie ich den Fehler weiter eingrenzen kann?
habe bei Asterisk das Modul chan_dongle hinzugefügt und es scheint auch zu funktionieren:
Der Huawei USB Stick wird auch erkannt:
dongle.conf wurde mit der IMEI Nummer versorgt:
Code:
[general]
interval=15 ; Number of seconds between trying to connect to devices
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
;jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
; Dongle channel. Defaults to "no". An enabled jitterbuffer will
; be used only if the sending side can create and the receiving
; side can not accept jitter. The Dongle channel can't accept jitter,
; thus an enabled jitterbuffer on the receive Dongle side will always
; be used if the sending side can create jitter.
;jbforce = no ; Forces the use of a jitterbuffer on the receive side of a Dongle
; channel. Defaults to "no".
;jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
;jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
; resynchronized. Useful to improve the quality of the voice, with
; big jumps in/broken timestamps, usually sent from exotic devices
; and programs. Defaults to 1000.
;jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a Dongle
; channel. Two implementations are currently available - "fixed"
; (with size always equals to jbmaxsize) and "adaptive" (with
; variable size, actually the new jb of IAX2). Defaults to fixed.
;jbtargetextra = 40 ; This option only affects the jb when 'jbimpl = adaptive' is set.
; The option represents the number of milliseconds by which the new jitter buffer
; will pad its size. the default is 40, so without modification, the new
; jitter buffer will set its size to the jitter value plus 40 milliseconds.
; increasing this value may help if your network normally has low jitter,
; but occasionally has spikes.
;jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------
[defaults]
; now you can set here any not required device settings as template
; sure you can overwrite in any [device] section this default values
context=default ; context for incoming calls, SMS and USSD
group=0 ; calling group
rxgain=0 ; increase the incoming volume; may be negative
txgain=0 ; increase the outgoint volume; may be negative
autodeletesms=yes ; auto delete incoming sms
resetdongle=yes ; reset dongle during initialization with ATZ command
u2diag=-1 ; set ^U2DIAG parameter on device (0 = disable everything except modem function)
; -1 not use ^U2DIAG command
usecallingpres=yes ; use the caller ID presentation or not
callingpres=allowed_passed_screen ; set caller ID presentation. By default use default network settings
; see [url]http://www.the-asterisk-book.com/unstable/applikationen-setcallerpres.html[/url]
disablesms=no ; disable of SMS reading from device when received. Enable this option to disable
; sms reception. Use smsaspdu=yes to avoid problem when SMS is too long in TEXT mode.
smsaspdu=yes ; if 'yes' send SMS in PDU mode.
language=en ; set channel default language
mindtmfgap=45 ; minimal interval from end of previews DTMF from begining of next in ms
mindtmfduration=80 ; minimal DTMF tone duration in ms
mindtmfinterval=200 ; minimal interval between ends of DTMF of same digits in ms
callwaiting=auto ; if 'yes' allow incoming calls waiting; by default use network settings
; if 'no' waiting calls just ignored
disable=no ; if 'yes' no load this device and just ignore this section
exten=+1234567890 ; exten for start incoming calls, only in case of Subscriber Number not available!,
; also set to CALLERID(dnid)
dtmf=relax ; control of incoming DTMF detection, possible values:
; off - off DTMF tone detection, voice data passed to asterisk unaltered
; use this value for gateways or if you do not use IVR in diaplan
; inband - do DTMF tones detection
; relax - like inband but with relaxdtmf option
; default is 'relax' for backward compatibility
; dongle required settings
[dongle0]
;audio=/dev/ttyUSB1 ; tty port for audio connection;
;data=/dev/ttyUSB2 ; tty port for AT commands;
; or you can omit both audio and data parameters and use imei=123456789012345 and/or imsi=612849384756451
; imei and imsi must contain exactly 15 digits !
; imei/imsi discovery is available on Linux only
imei=352215047829880
;imsi=612849384756451
; if you set audio and data parameter together with imei and/or imsi, audio and data is used.
; you can use both imei and imsi together. In this case exact match by imei and imsi is required.Und trotzdem findet Asterisk den USB Stick nicht.
Hat jemand eine Idee was ich noch tun muß oder wie ich den Fehler weiter eingrenzen kann?
