; (SCCP*)
;
; An implementation of Skinny Client Control Protocol (SCCP)
;
; Sergio Chersovani ([email protected])
; http://chan-sccp.belios.de
;
[general]
servername = Asterisk 1.4 ; show this name on the device registration
keepalive = 60 ; phone keep alive message evey 60 secs. Used to check the voicemail
debug = 1 ; console debug level. 1 => 10
context = outbound
dateFormat = D.M.Y ; M-D-Y in any order. Use M/D/YA (for 12h format)
bindaddr = 10.0.0.2 ; replace with the ip address of the asterisk server (RTP important param)
port = 2000 ; listen on port 2000 (Skinny, default)
disallow=all ; First disallow all codecs
allow=alaw ; Allow codecs in order of preference
;allow=ulaw ;
;allow=g729 ;
firstdigittimeout = 16 ; dialing timeout for the 1st digit
digittimeout = 8 ; more digits
;digittimeoutchar = # ; you can force the channel to dial with this char in the dialing state
autoanswer_ring_time = 1 ; ringing time in seconds for the autoanswer, the default is 0
autoanswer_tone = 0x32 ; autoanswer confirmation tone. For a complete list of tones: grep SKINNY_TONE sccp_protocol.h
; not all the tones can be played in a connected state, so you have to try.
remotehangup_tone = 0x32 ; passive hangup notification. 0 for none
transfer_tone = 0 ; confirmation tone on transfer. Works only between SCCP devices
callwaiting_tone = 0x2d ; sets to 0 to disable the callwaiting tone
musicclass=default ; Sets the default music on hold class
language=en ; Default language setting
;callevents=no ; generate manager events when phone
; performs events (e.g. hold)
;accountcode=skinny ; accountcode to ease billing
deny=0.0.0.0/0.0.0.0 ; Deny every address except for the only one allowed.
permit=10.0.0.0/255.255.255.224 ; Accept class A 10.0.0.1-31
; You may have multiple rules for masking traffic.
; Rules are processed from the first to the last.
; This General rule is valid for all incoming connections. It's the 1st filter.
localnet = 10.0.0.0/255.255.255.224 ; All RFC 1918 addresses are local networks
;externip = 1.2.3.4 ; IP Address that we're going to notify in RTP media stream
;externhost = mydomain.dyndns.org ; Hostname (if dynamic) that we're going to notify in RTP media stream
; externrefresh = 60 ; expire time in seconds for the hostname (dns resolution)
dnd = on ; turn on the dnd softkey for all devices. Valid values are "off", "on" (busy signal), "reject" (busy signal), "silent" (ringer = silent)
;;;rtptos = 184 ; sets the default rtp packets TOS
echocancel = on ; sets the phone echocancel for all devices
silencesuppression = off ; sets the silence suppression for all devices
callgroup=1 ; We are in caller groups 1,3,4. Valid for all lines
pickupgroup=1 ; We can do call pick-p for call group 1,3,4,5. Valid for all lines
amaflags = documentation ; Sets the default AMA flag code stored in the CDR record
trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT
; we don't have to trust the phone ip address, but the ip address of the connection
;;;tos = 0x68 ; call control packets tos (0x68 Assured forwarding)
;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none.
; The audio strem will be open in the progress and connected state.
private = on ; permit the private function softkey
;privacy = full ; full = disable hints notification on devices, on = hints showed depending on private key, off = hints always showed
mwilamp = on ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink
mwioncall = off ; Set the MWI on call.
blindtransferindication = ring ; moh or ring. the blind transfer should ring the caller or just play music on hold
;protocolversion = 5 ; skinny version protocol. Just for testing. 0 to 11
;cfwdall = off ; activate the callforward ALL stuff and softkeys
;cfwdbusy = off ; activate the callforward BUSY stuff and softkeys
;cfwdnoanswer = off ; activate the callforward NOANSWER stuff and softkeys
;devicetable=sccpdevice ;datebasetable for devices
;linetable=sccpline ;datebasetable for lines
;nat=on ; Global NAT support (default Off)
;directrtp=on ; This option allow devices to do direct RTP sessions (default Off)
;allowoverlap=on ; Enable overlap dialing support. (Default is off)
;;;callanswerorder=oldestfirst ; oldestfirst or lastestfirst
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
;jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
; sccp channel. Defaults to "no". An enabled jitterbuffer will
; be used only if the sending side can create and the receiving
; side can not accept jitter. The sccp channel can accept
; jitter, thus a jitterbuffer on the receive sccp side will be
; used only if it is forced and enabled.
;jbforce = no ; Forces the use of a jitterbuffer on the receive side of a sccp
; channel. Defaults to "no".
;jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
;jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
; resynchronized. Useful to improve the quality of the voice, with
; big jumps in/broken timestamps, usually sent from exotic devices
; and programs. Defaults to 1000.
;jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a
; sccp channel. Two implementations are currently available
; - "fixed" (with size always equals to jbmaxsize)
; - "adaptive" (with variable size, actually the new jb of IAX2).
; Defaults to fixed.
;jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
;-----------------------------------------------------------------------------------
[devices]
type = 7940 ; device type (see below)
autologin = alix ; lines list. You can add an empty line for an empty button (7960, 7970, 7940, 7920)
description = 7940G ; internal description. Not important
;addon = 7915 ; up to two addons can be defined per device
;keepalive = 60 ; set 0 to disable the keepalive check.
;tzoffset = +2
transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey
;park = on ; take a look to the compile howto. Park stuff is not compiled by default
speeddial = ; you can add an empty speedial if you want an empty button (7960, 7970, 7920)
;speeddial = 1000,name ; speeddial number and name
;serviceURL = ServiceURL1
cfwdall = off ; activate the callforward stuff and softkeys
cfwdbusy = off
cfwdnoanswer = off
pickupexten = off ; enable Pickup function to direct pickup an extension
;pickupcontext = sccp ; context where direct pickup search for extensions. if not set it will be ignored.
pickupmodeanswer = on ; on = asterisk way, the call has been answered when picked up
; off = call manager way, the phone who picked up the call rings the call
dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play.
; Some phone model does not play dtmf tones while connected (bug?), so the default is inband
;imageversion = P00308000800 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server)
;deny=0.0.0.0/0.0.0.0 ; Same as general
;permit=192.168.1.5/255.255.255.255 ; This device can register only using this ip address
dnd = on ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy signal), "reject" (busy signal), "silent" (ringer = silent) or user to toggle on phone
trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT
; we don't have to trust the phone ip address, but the ip address of the connection
;nat=on ; Device NAT support (default Off)
;directrtp=on ; This option allow devices to do direct RTP sessions (default Off)
;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none.
; The audio strem will be open in the progress and connected state.
private = on ; permit the private function softkey for this device
;privacy = full ; full = disable hints notification on devices, on = hints showed depending on private key, off = hints always showed
;mwilamp = on ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink
;mwioncall = off ; Set the MWI on call.
;setvar=testvar=value
device => SEP0013C307ECC8 ; device name SEP<MAC>
type = 7920 ; device type (see below)
autologin = alix-wifi ; lines list. You can add an empty line for an empty button (7960, 7970, 7940, 7920)
description = 7920 ; internal description. Not important
;keepalive = 60 ; set 0 to disable the keepalive check.
;tzoffset = +2
transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey
;park = on ; take a look to the compile howto. Park stuff is not compiled by default
speeddial = ; you can add an empty speedial if you want an empty button (7960, 7970, 7920)
;speeddial = 1000,name ; speeddial number and name
;serviceURL = ServiceURL1
cfwdall = off ; activate the callforward stuff and softkeys
cfwdbusy = off
cfwdnoanswer = off
pickupexten = off ; enable Pickup function to direct pickup an extension
;pickupcontext = sccp ; context where direct pickup search for extensions. if not set it will be ignored.
pickupmodeanswer = on ; on = asterisk way, the call has been answered when picked up
; off = call manager way, the phone who picked up the call rings the call
dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play.
; Some phone model does not play dtmf tones while connected (bug?), so the default is inband
;imageversion = P00403000200 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server)
;deny=0.0.0.0/0.0.0.0 ; Same as general
;permit=192.168.1.5/255.255.255.255 ; This device can register only using this ip address
dnd = on ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy signal), "reject" (busy signal), "silent" (ringer = silent) or user to toggle on phone
trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT
; we don't have to trust the phone ip address, but the ip address of the connection
;nat=on ; Device NAT support (default Off)
;directrtp=on ; This option allow devices to do direct RTP sessions (default Off)
;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none.
; The audio strem will be open in the progress and connected state.
private = on ; permit the private function softkey for this device
;privacy = full ; full = disable hints notification on devices, on = hints showed depending on private key, off = hints always showed
;mwilamp = on ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink
;mwioncall = off ; Set the MWI on call.
;setvar=testvar=value
device => SEP0013C3E22D20 ; device name SEP<MAC>
[lines]
id = 1001 ; future use
pin = 3972 ; future use
label = alix ; button line label (7960, 7970, 7940, 7920)
description = 7940G ; top diplay description
context = outbound
incominglimit = 2 ; more than 1 incoming call = call waiting.
transfer = on ; per line transfer capability. on, off, 1, 0
mailbox = 206559 ; voicemail.conf (syntax: vmbox[@context][:folder])
vmnum = 0# ; speeddial for voicemail administration, just a number to dial
;meetmenum = ; this extension will receive meetme requests, SCCP_MEETME_ROOM channel variable will
; contain the room number dialed into simpleswitch.
cid_name = ; caller id name
cid_num = 7940
;trnsfvm = 1001 ; extension to redirect the caller (e.g for voicemail)
secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits)
secondary_dialtone_tone = 0x22 ; outside dialtone
musicclass=default ; Sets the default music on hold class
language=en ; Default language setting
;accountcode=alix ; accountcode to ease billing
;;;rtptos = 184 ; sets the the rtp packets TOS for this line
echocancel = on ; sets the phone echocancel for this line
silencesuppression = off ; sets the silence suppression for this line
;callgroup=1,3-4 ; We are in caller groups 1,3,4. Valid for this line
;pickupgroup=1,3-5 ; We can do call pick-p for call group 1,3,4,5. Valid for this line
;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line
;setvar=testvar2=value
line => alix
id = 1002 ; future use
pin = 3972 ; future use
label = alix ; button line label (7960, 7970, 7940, 7920)
description = 7920 ; top diplay description
context = outbound
incominglimit = 2 ; more than 1 incoming call = call waiting.
transfer = on ; per line transfer capability. on, off, 1, 0
mailbox = 206559 ; voicemail.conf (syntax: vmbox[@context][:folder])
vmnum = 0# ; speeddial for voicemail administration, just a number to dial
;meetmenum = ; this extension will receive meetme requests, SCCP_MEETME_ROOM channel variable will
; contain the room number dialed into simpleswitch.
cid_name = ; caller id name
cid_num = 7920
;trnsfvm = 1002 ; extension to redirect the caller (e.g for voicemail)
secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits)
secondary_dialtone_tone = 0x22 ; outside dialtone
musicclass=default ; Sets the default music on hold class
language=en ; Default language setting
;accountcode=alix-wifi ; accountcode to ease billing
;;;rtptos = 184 ; sets the the rtp packets TOS for this line
echocancel = on ; sets the phone echocancel for this line
silencesuppression = off ; sets the silence suppression for this line
;callgroup=1,3-4 ; We are in caller groups 1,3,4. Valid for this line
;pickupgroup=1,3-5 ; We can do call pick-p for call group 1,3,4,5. Valid for this line
;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line
;setvar=testvar2=value
line => alix-wifi
