Hallo,
ich habe folgendes Problem: Ich habe einen Asterisk Server mit AVM Fritz Card chan_Capi cm 0.61 hinter einer ISDN ANlage.
Der Asterisk hat einen S0 Bus zugewiesen mit der MSN 514 und die Nebenstellen 1526, 1527, 1528.
Nun kann ich vom Asterisk heraus telefonieren, aber es kommen keine Anrufe vom ISDN Netz zum Asterisk?
capi conf:
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
;ulaw=yes ;set this, if you live in u-law world instead of a-law
; interface sections ...
[ISDN1] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;ntmode=yes ;if isdn card operates in nt mode, set this to yes
isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;capi controller number to use
group=1 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
accountcode= ;Asterisk accountcode to use in CDRs
context=capi ;context for incoming calls
holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and Asterisk may
;play MOH.
immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;Asterisk call group
devices=2 ;number of concurrent calls on this controller
;(2 makes sense for single BRI, 30 for PRI)
extensions.conf
[capi]
exten => _X.,1,SetCallerID(514)
exten => _X.,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => _X.,3,Hangup
exten => 5141526,1,SetCallerID(1526)
exten => 5141526,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141526,3,Hangup
exten => 5141527,1,SetCallerID(1527)
exten => 5141527,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141527,3,Hangup
exten => 5141528,1,SetCallerID(1528)
exten => 5141528,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141528,3,Hangup
Kann mir jemand helfen?
Danke!
ich habe folgendes Problem: Ich habe einen Asterisk Server mit AVM Fritz Card chan_Capi cm 0.61 hinter einer ISDN ANlage.
Der Asterisk hat einen S0 Bus zugewiesen mit der MSN 514 und die Nebenstellen 1526, 1527, 1528.
Nun kann ich vom Asterisk heraus telefonieren, aber es kommen keine Anrufe vom ISDN Netz zum Asterisk?
capi conf:
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
;ulaw=yes ;set this, if you live in u-law world instead of a-law
; interface sections ...
[ISDN1] ;this example interface gets name 'ISDN1' and may be any
;name not starting with 'g' or 'contr'.
;ntmode=yes ;if isdn card operates in nt mode, set this to yes
isdnmode=msn ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
;when using NT-mode, 'DID' should be set in any case
incomingmsn=* ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123 ;set a default caller id to that interface for dial-out,
;this caller id will be used when dial option 'd' is set.
;controller=0 ;ISDN4BSD default
;controller=7 ;ISDN4BSD USB default
controller=1 ;capi controller number to use
group=1 ;dialout group
;prefix=0 ;set a prefix to calling number on incoming calls
softdtmf=on ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=on ;in addition to softdtmf, you can use relaxed dtmf detection
accountcode= ;Asterisk accountcode to use in CDRs
context=capi ;context for incoming calls
holdtype=hold ;when Asterisk puts the call on hold, ISDN HOLD will be used. If
;set to 'local' (default value), no hold is done and Asterisk may
;play MOH.
immediate=yes ;DID: immediate start of pbx with extension 's' if no digits were
; received on incoming call (no destination number yet)
;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
; info like REDIRECTINGNUMBER may be lost, but this is necessary for
; drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1 ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes ;EICON DIVA SERVER (CAPI) echo cancelation
;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64 ;echo cancel tail setting
;bridge=yes ;native bridging (CAPI line interconnect) if available
;callgroup=1 ;Asterisk call group
devices=2 ;number of concurrent calls on this controller
;(2 makes sense for single BRI, 30 for PRI)
extensions.conf
[capi]
exten => _X.,1,SetCallerID(514)
exten => _X.,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => _X.,3,Hangup
exten => 5141526,1,SetCallerID(1526)
exten => 5141526,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141526,3,Hangup
exten => 5141527,1,SetCallerID(1527)
exten => 5141527,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141527,3,Hangup
exten => 5141528,1,SetCallerID(1528)
exten => 5141528,2,Dial(CAPI/contr1/${CALLERIDNUM}:${EXTEN:1}/b)
exten => 5141528,3,Hangup
Kann mir jemand helfen?
Danke!
