FBF 7270 und Kabel-Deutschland

[general]
context=default
bindport=5061
bindaddr=192.168.6.1
srvlookup=yes

; --------------------------------------------------------------------
;
; hier koennten die Anmeldedaten für VoIP Provider stehen
; dazu kommen wir in einer spaeteren Lektion
;


; --------------------------------------------------------------------
;
; hier kommen die Anmeldekontexte für die SIP Endgeraete 30-39
;



[7701]
context=sip7701
callerid="TestSIP 7701" <7701>
host=dynamic
domain=192.168.6.1
type=friend
user=7701
secret=7701
nat=yes
;mailbox=7701
canreinvite=no                ; Typically set to NO if behind NAT

;regexten=1234                 ; When they register, create extension 1234
;username=xlite1
disallow=all
allow=gsm                     ; GSM consumes far less bandwidth than ulaw
allow=ulaw
allow=alaw

[7702]
context=sip7702
callerid="X-Lite 7702" <7702>
host=dynamic
domain=192.168.6.1
nat=yes                       ; X-Lite is behind a NAT router
type=friend
user=7702
secret=7702
;mailbox=7702
canreinvite=no                ; Typically set to NO if behind NAT

;regexten=1234                 ; When they register, create extension 1234
username=xlite1
disallow=all
allow=gsm                     ; GSM consumes far less bandwidth than ulaw
allow=ulaw
allow=alaw

[7703]
context=sip7703
callerid="TestSIP 7703" <7703>
host=dynamic
domain=192.168.6.1
nat=yes                       ; X-Lite is behind a NAT router
type=friend
user=7703
secret=7703
;mailbox=7703
canreinvite=no                ; Typically set to NO if behind NAT

;regexten=1234                 ; When they register, create extension 1234
;username=xlite1


[7704]
context=sip7704
callerid="TestSIP 7704" <7704>
host=dynamic
domain=192.168.6.1
nat=yes                       ; X-Lite is behind a NAT router
type=friend
user=7704
secret=7704
;mailbox=7704
;canreinvite=no                ; Typically set to NO if behind NAT

;regexten=1234                 ; When they register, create extension 1234
;username=xlite1


; sip external outgoing


[7707]
context=from_fritzbox
callerid="Fritzbox" <7707>
host=dynamic
domain=192.168.6.1
type=friend
user=7707
secret=7707
disallow=all
allow=gsm
allow=ulaw
allow=alaw

[globals]
CAPI_CALLERID= xxx; bisher hatte ich hier die Rufnummer ohne Vorwahl stehen, oder muss da eine MSN rein?

[general]
static=yes
writeprotect=no

; --------------------------------------------------------------------
; Es hat sich als gute Praxis erwiesen, die Inhalte der Datei
; extensions.conf modular aufzubauen. Diese Praxis wollen
; wir auch hier anwenden
;

[lokal]
; Erreichbarkeit der Nebenstellen 7701-7707
; untereinander herstellen

exten => _7X,1,NoCDR()
exten => _77XX,1,Dial(SIP/${EXTEN},55,Ttr)

; --------------------------------------------------------------------
;
; hier kommt der default-Context, in dem alle Geraete in der
; Grundkonfiguration erstmal laufen.
; Alle Geraete koennen sich gegenseitig anrufen

[festnetz_out]
; Raus-Telefonieren
exten => _X.,1,Set(CALLERID(ani)=(${CAPI_CALLERID})
exten => _X.,n,Dial(CAPI/ISDN3/${EXTEN},55,Tt/bd)

[default]
include => lokal

exten => 1001,1,Answer()
exten => 1001,2,Playback(hello-world)
exten => 1001,3,Hangup()


[sip7701]
include => lokal
include => festnetz_out


[sip7702]
include => lokal
include => festnetz_out


[sip7703]
include => lokal
include => festnetz_out


[sip7704]
include => lokal
include => festnetz_out


[sip7707]
include => lokal
include => festnetz_out


[capi_in3]
exten => _X.,1,noop(${CALLERID(all)})
exten => _X.,n,Dial(SIP/7702)

; CAPI config
; (1234567 gets replaced by script cfg_asterisk start)
;

; general section

[general]
nationalprefix=0
internationalprefix=00
rxgain=1.0       ;linear receive gain (1.0 = no change)
txgain=1.0       ;linear transmit gain (1.0 = no change)
language=de      ;set default language (en/de...)
;ulaw=yes        ;set this, if you live in u-law world instead of a-law

;jb.....         ;with Asterisk 1.4 you can configure jitterbuffer,
                 ;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.

; interface sections ...
[ISDN1]          ; fritzbox 7050/7170 external S0 (or external analog line: experimental)
ntmode=yes      ;if isdn card operates in nt mode, set this to yes
isdnmode=DID     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * = any,
defaultcid=2661241  ;set a default caller id to that interface for dial-out,
                 ;this caller id will be used when dial option 'd' is set.
controller=4     ;capi controller number to use (=4: fritzbox 7050/7150 at analog line)
group=1          ;dialout group
softdtmf=off      ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=off     ;in addition to softdtmf, you can use relaxed dtmf detection
accountcode=     ;PBX accountcode to use in CDRs
context=int-so  ;context for incoming calls
;holdtype=hold   ;when the PBX puts the call on hold, ISDN HOLD will be used. If
                 ;set to 'local' (default value), no hold is done and the PBX may
                 ;play MOH.
bridge=no      ;native bridging (CAPI line interconnect) if available
devices=2        ;number of concurrent calls on this controller
                 ;(2 makes sense for single BRI, 30 for PRI)


[ISDN3]          ; fritzbox 7050 internal S0
ntmode=no      ;if isdn card operates in nt mode, set this to yes
isdnmode=MSN     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
                 ;when using NT-mode, 'DID' should be set in any case
incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * = any
defaultcid=xxx  ;hier steht die Rufnummer ohne Vorwahl
                     ;set a default caller id to that interface for dial-out,
                 ;this caller id will be used when dial option 'd' is set.
controller=3     ;capi controller number to use
group=3          ;dialout group
softdtmf=off      ;enable/disable software dtmf detection, recommended for AVM cards
relaxdtmf=off     ;in addition to softdtmf, you can use relaxed dtmf detection
;accountcode=     ;PBX accountcode to use in CDRs
context=capi_in3  ;context for incoming calls
;holdtype=hold   ;when the PBX puts the call on hold, ISDN HOLD will be used. If
                 ;set to 'local' (default value), no hold is done and the PBX may
                 ;play MOH.
immediate=yes   ;DID: immediate start of pbx with extension 's' if no digits were
                 ;     received on incoming call (no destination number yet)
                 ;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
                 ;     info like REDIRECTINGNUMBER may be lost, but this is necessary for
                 ;     drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
bridge=no      ;native bridging (CAPI line interconnect) if available
devices=2        ;number of concurrent calls on this controller
                 ;(2 makes sense for single BRI, 30 for PRI)


; unused example (reference)

;[ISDN9]          ;this example interface gets name 'ISDN9' and may be any
                 ;name not starting with 'g' or 'contr'.
                 ;Use one interface section for each isdn port!
;ntmode=yes      ;if isdn card operates in nt mode, set this to yes
;isdnmode=did     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
                 ;when using NT-mode, 'DID' should be set in any case
;incomingmsn=8001,8002 ;allow incoming calls to this list of MSNs/DIDs, * = any
;defaultcid=123  ;set a default caller id to that interface for dial-out,
                 ;this caller id will be used when dial option 'd' is set.
;controller=0    ;ISDN4BSD default
;controller=7    ;ISDN4BSD USB default
;controller=1     ;capi controller number of this interface/port
;group=1          ;dialout group
;prefix=0        ;set a prefix to calling number on incoming calls
;softdtmf=on      ;enable/disable software dtmf detection, recommended for AVM cards
;relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf detection
;faxdetect=off    ;enable faxdetection and redirection to EXTEN 'fax' for incoming and/or
                 ;outgoing calls. (default='off', possible values: 'incoming','outgoing','both')
;accountcode=     ;PBX accountcode to use in CDRs
;amaflags=default;AMA flags for CDR ('default', 'omit', 'billing', or 'documentation')
;context=capi_in  ;context for incoming calls
;holdtype=hold   ;when the PBX puts the call on hold, ISDN HOLD will be used. If
                 ;set to 'local' (default value), no hold is done and the PBX may
                 ;play MOH.
;immediate=yes   ;DID: immediate start of pbx with extension 's' if no digits were
                 ;     received on incoming call (no destination number yet)
                 ;MSN: start pbx on CONNECT_IND and don't wait for SETUP/SENDING-COMPLETE.
                 ;     info like REDIRECTINGNUMBER may be lost, but this is necessary for
                 ;     drivers/pbx/telco which does not send SETUP or SENDING-COMPLETE.
;echosquelch=1   ;_VERY_PRIMITIVE_ echo suppression
;echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation (yes=g165)
                 ;(possible values: 'no', 'yes', 'force', 'g164', 'g165') 
;echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)
;echotail=64     ;echo cancel tail setting (default=0 for maximum)
;echocancelnlp=1 ;activate non-linear-processing; this improves echo cancel ratio, but might
                 ;incorporate variable gain in the signal path.
;bridge=yes      ;native bridging (CAPI line interconnect) if available
;callgroup=1     ;PBX call group
;pickupgroup=1   ;PBX pickup group (which call groups are we allowed to pickup)
;language=de     ;set language for this device (overwrites default language)
;disallow=all    ;RTP codec selection (valid with Eicon DIVA Server only)
;allow=all       ;RTP codec selection (valid with Eicon DIVA Server only)
;devices=2        ;number of concurrent calls (b-channels) on this controller
                 ;(2 makes sense for single BRI, 30/23 for PRI/T1)
;jb.....         ;with Asterisk 1.4 you can configure jitterbuffer,
                 ;see Asterisk documentation for all jb* setting available.
;mohinterpret=default ;Asterisk 1.4: default music on hold class when placed on hold.
;qsig=on         ;enable use of Q.SIG extensions.