root:~> U-Boot 1.1.5 (May 5 2007 - 05:46:05)
CPU: ADSP BF532 Rev.: 0.5
Board: IP04 IP-PBX
http://www.rowetel.com/ucasterisk/ip04.html
Clock: VCO: 400 MHz, Core: 400 MHz, System: 133 MHz
SDRAM: 64 MB
In: serial
Out: serial
Err: serial
256 MiB
DM9000#0
starting from spi flash
Hit any key to stop autoboot: 0
Loading from device 0: NAND 256MiB 3,3V 8-bit (offset 0x0)
Image Name: uClinux Kernel and ext2
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 4729008 Bytes = 4.5 MB
Load Address: 00001000
Entry Point: 00001000
Automatic boot of image at addr 0x02000000 ...
## Booting image at 02000000 ...
Image Name: uClinux Kernel and ext2
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 4729008 Bytes = 4.5 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.19.3-ADI-2007R1-bf1-svn (root@AlexHome) (gcc version 4.1.1 (ADI 07R1)) #1 Thu Sep 6 23:46:10 EDT 2007
Blackfin support (C) 2004-2006 Analog Devices, Inc.
Compiled for ADSP-BF532 Rev. 0.5
Blackfin uClinux support by http://blackfin.uclinux.org/
Processor Speed: 400 MHz core clock and 133 Mhz System Clock
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
text = 0x00001000-0x0019205c
init = 0x00193000-0x001a54f4
data = 0x001a75b8-0x001ed4b0
stack = 0x001a8000-0x001aa000
bss = 0x001ed4b0-0x00220660
available = 0x00220660-0x03200000
rootfs = 0x03200000-0x03f00000
DMA Zone = 0x03f00000-0x04000000
Instruction Cache Enabled
Data Cache Enabled (write-through)
Hardware Trace Enabled
Built 1 zonelists. Total pages: 12700
Kernel command line: root=/dev/mtdblock2 rw ethaddr=00:09:45:54:20:ca ip=192.168.1.30:192.168.1.200:192.168.1.1:255.255.255.0:BF1:eth0:off
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Physical pages: 3200
Memory available: 48384k/63842k RAM, (73k init code, 1604k kernel code, 204k data, 1024k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin Instruction SRAM: 32 KB
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Blackfin GPIO Controller
Blackfin DMA Controller
bf1_init(): chip_id=527A50CB,dspid=E5040005
bf1_init(): registering device resources
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
yaffs Sep 6 2007 23:42:25 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
Dynamic Power Management Controller Driver v0.1: major=10, minor = 254
Serial: Blackfin serial driver
bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
dm9000 Ethernet Driver
eth0: dm9000 at 20100000,20100002 IRQ 48 MAC: 00:09:45:54:20:ca
BF5xx flash: probing 16-bit flash bus for cfi_probe
BF5xx flash: probing 16-bit flash bus for smt_flash
BF5xx flash: probing 16-bit flash bus for jedec_probe
uclinux[mtd]: RAM probe address=0x3200000 size=0xd00000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00d00000 : "ROMfs"
uclinux[mtd]: set ROMfs:EXT2 to be root filesystem
Generic platform RAM MTD, (c) 2004 Simtec Electronics
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 649 at 0x05120000
Bad eraseblock 1189 at 0x094a0000
Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00800000 : "linux kernel"
0x00800000-0x10000000 : "file system"
mice: PS/2 mouse device common for all mice
cs_mask: 0x20, baud=0x0, flag=0x0, ctrl=0xff00, dir=0x4
Zapata Telephony Interface Registered on major 196
Zaptel Version: SVN-trunk-r1501 Echo Canceller: MG2
Code test: code function addr = 0x000f54c4
dma_alloc_init: dma_page @ 0x03009000 - 256 pages at 0x03f00000
port: 1 port_type: O
port: 2 port_type: S
port: 3 port_type: S
port: 4 port_type: S
port: 5 port_type: -
port: 6 port_type: -
port: 7 port_type: -
port: 8 port_type: -
Module 0: Installed -- AUTO FXO (FCC mode)
ProSLIC module is Si3215
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc7
reg 83: 0xc7
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc7
reg 83: 0xc7
Start automatic calibration
Module 1: Installed -- AUTO FXS
ProSLIC module is Si3215
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc6
reg 83: 0xc6
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc6
reg 83: 0xc6
Start automatic calibration
Module 2: Installed -- AUTO FXS
ProSLIC module is Si3215
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc5
reg 83: 0xc5
reg 0: 0x3
reg 14: 0x0
reg 74: 0x32
reg 80: 0x0
reg 81: 0x0
reg 92: 0xff
reg 82: 0xc5
reg 83: 0xc5
Start automatic calibration
Module 3: Installed -- AUTO FXS
Found: Blackfin STAMP (8 modules)
wcfxs_init_ok = 1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Blackfin dm9000 interrupt setup: DEMUX_GPIO irq 48
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.1.30, mask=255.255.255.0, gw=192.168.1.1,
host=BF1, domain=, nis-domain=(none),
bootserver=192.168.1.200, rootserver=192.168.1.200, rootpath=
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs2
block 586 is bad
block 1126 is bad
VFS: Mounted root (yaffs filesystem).
Freeing unused kernel memory: 72k freed (0x193000 - 0x1a4000)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
devpts: called with bogus options
We already have unpacked Asterisk configuration...
rm: cannot remove '/defaults.tgz': No such file or directory
mv: cannot rename '/bin/gui_custommenus.conf': No such file or directory
Looking for host 192.43.244.18 and service ntp
host found : time.nist.gov
Registered tone zone 0 (United States / North America)
Starting Asterisk...
Welcome to:
____ _ _
/ __| ||_| _ _
_ _| | | | _ ____ _ _ \ \/ /
| | | | | | || | _ \| | | | \ /
| |_| | |__| || | | | | |_| | / \
| ___\____|_||_|_| |_|\____|/_/\_\
|_| IP04 Open Hardware IP-PBX
For further information see:
http://www.rowetel.com/ucasterisk/ip04.html
Thanks to the Astfin, BlackfinOne, Asterisk and Blackfin communities.
BusyBox v1.4.1 (2007-09-06 23:55:25 EDT) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
root:~> 1 Jan 00:00:13 ntpdate[51]: no server suitable for synchronization found
root:~>
